10 Simple Ways To Figure Out Your Car Key Button Repair
Car Key Button Repair
A broken car key button can be frustrating. You may need to call an emergency locksmith service that is available 24 hours a day for assistance or to purchase a new remote.
But, you may be able to save money by repairing an old key fob rather than replacing it. This is especially true when the switch is worn out or has faulty contacts are the reason for the problem.
Battery
If the buttons on the key fob aren't responding to pressing, it could be an obvious indication that your battery is dying or nearing the end of its lifespan. Fortunately replacing the battery is a simple task that can be completed on your own rather than hiring a locksmith to do it for you.
First, locate the battery compartment. It is typically located on the backside of the key fob. It could be hidden behind the cover, which slides out, or an access point which opens when you press the button. When the compartment is open then you will find the small battery. It's usually shaped as an oblong coin and is identified with an minus and plus sign. Take the battery out and replace it with a new one in its place, ensuring that the plus and minus symbols are aligned correctly.
Close the compartment and snap the two parts of your key fob. Make sure to align the parts and snap them into place correctly prior to closing the door and testing your keys. To verify that the buttons function correctly Press any of them.
If the remote key fob you have purchased stops functioning even after replacing the battery, it might be experiencing other issues that require a different type of repair. Dropping the fob in a puddle could cause it to stop functioning. It could also be suffering from an electrical issue within the device or it may require to be deprogrammed by a locksmith or locksmith. Try to figure out if car key immobiliser repair is related to your key fob applying these other typical methods for troubleshooting your car.
Switches
Depending on the year and the model, there are a variety of kinds of switches available that are used in the keyfob of your car. The older style key has an electronic chip that is visible in the case. The latest keys operate by sending signals to your car. Whatever the model of key, the buttons on the key may become worn out or damaged with normal use. As a result, they become difficult to press or even ineffective. If you force the button it can cause further damage. It could also stop the key from working in the future.
If you can't get your key to function, try changing the batteries. If this doesn't work, you may have to clean your key fob or re-adjust its switches. These tiny electronic switches are more susceptible than larger components of the key to break since they are constantly jostled.
The switches are rubber-like and are coated with an electrically conducting film that wears down over time. Luckily, they're also tiny and cheap to replace. The old ones are soldered to the circuit board, and you'll need to be careful to remove them without causing any damage to anything else. Then, you can solder in the new ones and reassemble your key fob.
A good way to keep your car key fob from becoming damaged is to not use it for longer than a couple of hours at a time, and also to not leave it in places that it will be visible. When you're not using your key, keep it in a secure place.
If the issue persists after you have cleaned your key fob or battery, and attempted to clean it, then you may need to consult an expert locksmith. A professional locksmith can check the frequency of your key to determine whether your car is able to communicate. They can also open and replace microswitches, change cases, and much more.
Outer Case
If the buttons can't move freely up and down the case, they could get stuck or break. If cleaning the case with rubbing alcohol and a cotton swab doesn't work, it might be necessary to take off the case. If the contacts that the buttons touch aren't a good fit, or if they are worn, changing them might be the only option.
Rubber buttons can wear out over the years. The rubber expands and nails cut into it, and the buttons become difficult to press. This can cause the key to fail, and in this case it's time for the replacement of the case or buttons. This repair involves disassembling the remote, locating the button switches on the circuit board, and then heating the solder, and then carefully taking them off. New buttons are then soldered to the circuit board. The case can then be reassembled and the horse shoe key blade piece inserted. The new buttons must be a close fit into the case in order to prevent them from falling out.
Inner Case
Over time, your key fob's buttons could become damaged or stuck due to the constant jostling and accidental pressing. Utilizing metallic tape and a hole-punch, you can solve this issue in the event that your vehicle is not at home and the key fob won't work, allowing you to unlock the doors, but not to start the engine. This simple fix can allow you to return safely to your vehicle to finish your trip.